Practical with its pockets and reinforcements!
---specs---
WATERPROOFING
- Dual-layer hydrophilic fabric
- >10000 mm of water pressure.
- Fully taped seams.
- Inner flap
- Bottom of the legs adjustable by rip-tab strip.
- Tested under a simulated heavy rain shower (119 gal/hr/sqm) for 4 hours.
BREATHABILITY
RET <12: very breathable.
To find out whether a fabric is breathable, we measure its evaporative resistance, or RET, (test based on the ISO 11092 standard). It is its ability to allow the water vapor produced by the body during exercise to escape.
COMFORT
- The waist is adjustable using semi-elasticated rip-tabs.
REFLECTIVE
A large reflective 3M patch on the back intensifies low light sources. The Tribord logos are also reflective.
RESISTANCE TO WEAR
- Injected plastic central zipper resistant to salt oxidation.
HOW TO REACTIVATE THE JACKETand#x27;S WATER REPELLENCY \nstep 1: before washing
Close all zippers and flaps and remove any parts of the garment that cannot be washed. Also remember to loosen the straps and elastic parts and empty the pockets.
Then turn the garment inside out to wash it.
HOW TO REACTIVATE THE JACKETand#x27;S WATER REPELLENCY \nstep 2: washing
You can wash your jacket on a synthetic cycle at 86°F or 104°F with your usual detergent. Do not use fabric conditioner, which could damage the existing performance of the garment, or bleach.
Also take care not to bend your jacket too much when you place it in the washing machine and do not overload your machine.
Very important: select a thorough rinse or double rinse to completely remove all detergent residue.
HOW TO REACTIVATE THE JACKETand#x27;S WATER REPELLENCY \nstep 3: drying
Drying is a crucial phase in reactivating the water repellent treatment.
We recommend that you lay your jacket flat on a clothes rack and leave it out to dry in the open. Caution: never dry your jacket directly on a radiator.
Then place it in the tumble dryer on a short synthetics cycle, i.e. 10 to 15 minutes, before turning it back the right way round.
HOW TO REACTIVATE THE JACKETand#x27;S WATER REPELLENCY
If, despite this procedure of washing and thorough rinsing followed by gentle drying in a tumble dryer, the drops of water no longer run off the surface of your jacket, we recommend that you "re-waterproof" it using a waterproofing spray or detergent sold in our stores.
Composition
Main fabric : 100.0% Polyamide \r\nMain lining : 100.0% Polyester cationic\r\nSecondary lining : 100.0% Polyamide \r\nYoke : 100.0% Polyester cationic
Storage Instructions
Store in a dry place, but do not leave your garment on a heat source such as a radiator, as this may damage the breathable membrane or coating.
Care Instructions
Machine wash your Offshoroa waterproof and breathable salopettes at 86°F. Inside-out with hook and loop strips stuck together. Choose a long rinse and gentle spin cycle. Line dry if possible. Occasional tumble drying on low for a short period of time will improve the water repellent treatment. To reactivate the water repellent treatment, you can also iron the fabric at a maximum temperature of 284°F or apply the Tribord re-waterproofing spray.
Guarantee
2 Years
---/specs---
---catchline---
These salopettes, especially designed to provide protection, are waterproof and breathable. Zipped fleece-lined pockets will be a shelter for your hands.
---/catchline---
---features---
Waterproof
4 hours under heavy rain (andgt;10000 mm). Fully taped seams. Water repellent.
Salt water resistant
Injected plastic zipper. Treated coating.
Breathability
Very breathable (RETandlt;12)
Pockets
3 secure pockets (2 fleece, 1 on the thigh)
Abrasion resistant
Seat, knee and ankle reinforcements to resist wear.
Easy to use
Adjustable ankles, high cut for better chest protection.
---/features---
---made_for---
regular inshore sailors. less than two weeks of sailing per year in heavy rain.
---/made_for---
---videos---
1286984,p1114937
---/videos---
